The EverStart Maxx Battery Charger is designed for use in emergency situations, such as the power going out. Connect to heavy gauge metal part of the frame or engine block. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. First, make sure that the battery is inserted correctly into the light. Check the whole length of the power cord for fraying or other damage on your laptop. To stop charging, press the charge button. Do not over-tighten as this will damage the housing. Do not open the battery charger there are no user-serviceable parts inside. Position the unit as desired on a flat wall surface near a functioning AC outlet. The unit has two mounting backets at the corners of the unit. A: The final current level and the peak charging voltage when this current is flowing are the two factors that determine whether a battery is fully charged. Receptacles are available having built in GFCI protection and may be used for this measure of safety. Your email address will not be published. This device complies with part 15 of the FCC rules. Do not operate near flammable materials, fumes or gases. For a battery without cell caps (maintenance free), carefully follow manufacturers charging instructions. If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturers option. EverStart Battery Charger Maxx BC40BE Instruction manual (8 pages) 3. The following can be done to fix this: Allow the battery to warm up or cool down. Ensure that unit is completely disconnected from battery and power source before cleaning. Motors may spark, and the sparks might ignite fumes. Do not operate this unit in a closed area or restrict ventilation in any way. 2020 Baccus Global LLC Boca Raton, FL 33487 (877) 571-2391 BC4WE_ManualENSP_032620.indd 16-1 3/28/2020 4:34:23 PM. Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Study all battery manufacturers specific precautions, such as removing or not removing cell caps while charging, and recommended rates of charge. If you want to hang something from the ceiling, you can try using a large picture hanging hook or a wire hanger. FEATURES LCD Screen Charge / Voltage Button Engine Start Button Alternator Check Button Battery Recondition Button Negative (Black) Clamp Positive (Red) Clamp 120V AC Cord Storage Tabs 120V AC Plug In a pinch, other rechargeable AA or AAA batteries should work. When the Charging/Charged LED lights solid, the charging process is complete. The best way to inspect the battery is by using a voltmeter. Help Call customer service hotline 1-877-571-2391 4A WATERPROOF BATTERY CHARGER/MAINTAINER SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. If in doubt, use the next heavier gauge. RISK OF UNSAFE OPERATION. This equipment employs parts (switches, relays, etc.) Follow the steps outlined in the Important Safety Instructions section of this manual. ManualsDock also connects a growing community of active product owners with self-help and product knowledge, there are thousands of manuals from hundreds of big manufacturers. A lead acid battery can produce a short circuit current high enough to weld a ring, or similar metal object, to skin causing a severe burn. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Determine voltage of the battery to be charged by referring to the vehicle manual. To reduce the risk of electric shock, unplug the battery charger from the outlet before attempting any maintenance or cleaning. Be aware of first aid procedures in case of accidental contact with battery acid. Attach clamps to battery and chassis as indicated in the appropriate section. The Everstart Maxx flashlight has a sleek, modern design and is available in several colors. Never allow battery acid to come in contact with this unit. Q: How can I tell when a battery on a charger is fully charged? Battery recondition sends a series of electrical pulses to break up the crystalline form of lead sulfate and turn these chemicals into useful battery electrolytes. Marine batteries must be removed and charged on shore. The hanging hook can also be used to conveniently position the unit. WARNING: The use of any accessory not recommended for use with this home appliances could be hazardous. This unit is NOT designed for such use. Use the unit for charging/boosting a 12 volt battery only. For safety reasons, use a knife to pry open the top of the light after removing the rubber piece that covers the screws which hold the top cover in place. To reduce risk of a spark near the battery: When disconnecting charger, disconnect AC Power cord, remove clamp from vehicle chassis, and then remove clamp from battery terminal. The LCD screen will display the following: To stop the reconditioning process, press the battery recondition button again. Schumacher 12V 250A ProSeries Battery Charger/Engine Starter 1 $37.99 AC DC 12V/8A 24V/4A Automatic Car Battery Charger,Zengest Trickle Battery Charger, Power Battery Maintainer for Car, Automotive, Vehicle, Motorcycle $21.18 12V 6A Smart Fast Lead-Acid Battery Charger For Car Motorcycle Lcd Display Eu +2 options $100.99 (2) Return the product to the retailer where product was purchased for an exchange (provided that the store is a participating retailer). Once you have determined how much voltage is remaining in the battery, you can decide if it is necessary to charge the battery. WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS DANGEROUS. Make sure youre using a high-quality replacement battery because cheap ones will ruin your flashlight and turn it into a how to charge everstart maxx flashlight. Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 1-877-571-2391. AGM and lead acid batteries are both available in the EverStart series. WARNING To reduce the risk of injury or property damage: The chargers output leads have color-coded battery clamps (REDPOSITIVE and BLACKNEGATIVE). Q: Can I let the battery in my car charge overnight? Reorient or relocate the receiving antenna. A: Yes, the power banks intelligent circuitry regulates the batterys charge. Read and understand all warnings and operating instructions before using any tool or equipment. THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY ADULTS. I'm Jennifer, and I love everything about lighting. WARNING: The use of any accessory not recommended for use with this home appliance could be hazardous. This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product. If the vehicle accessory outlet fuse opens (blows) when plugging in this battery charger, do not use this battery charger with this vehicle accessory outlet: Do not replace the vehicle accessory outlet fuse with one of a higher amperage rating. Turning off the controls will not reduce this risk. Dont use the battery charger in damp or wet locations. Do not attempt to defeat this safety feature. If battery acid contacts skin or clothing, wash immediately with soap and water for at least 10 minutes and get medical attention immediately. Position AC and clamp cords to reduce risk of damage by hood, door, or moving engine part. When the unit is properly connected, press the charge/voltage button to start the charging process. Connect NEGATIVE (BLACK) clamp to vehicle chassis or engine block away from battery. The Positive post (marked POS,P, +) usually has a larger diameter than the Negative battery post (marked NEG, N, ). Stand as far back from the battery as possible, and do not face battery when making final connection. Input: 120V AC, 60Hz, 0.9A If your flashlight has a spring, you can use pliers to attach the red wire easily. Call customer service hotline 1-877-571-2391 SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. These rings connect directly to the corresponding connectors on the battery posts. Johnson Controls produces EverStart batteries. The Charging/Charged LED will flash green to indicate the unit is in charging mode. Charger Location 1. On the other side, if you use a quick charger you can recharge it in less than 6 hours. If it still does not fit, contact a qualified electrician. To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. Never place charger directly above battery being charged; gases from battery will corrode and damage charger. This unit was designed for household use only. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Insert a new 18650 rechargeable Li-ion battery into the light. If the voltage is below 3 volts, the battery needs to be charged. The most popular AGM (absorbed glass mat) battery models are EverStart Plus and EverStart Maxx BC4WE 4 Amp Battery Charger. Consult the dealer or an experienced radio/TV technician for help. Do not overfill. Increase the separation between equipment and receiver. Proof of purchase may be required by manufacturer. Q: What is the turnaround time for a 12-volt battery? Price and other details may vary based on product size and color. You can then remove the batteries, metal plate, and black wire from the light. To maintain the operating condition and maximize the life of the charger cords, always coil them loosely for storage. The Everstart MAXX 3 Amp 6V / 12V automotive charger and maintainer is a flexible solution for practically any garage. Recommended accessories for use with your tool may be available from the manufacturer. Always disconnect the charger at AC power source and at battery terminal before mounting the unit. Pull by plug rather than cord when unplugging the unit. Connect to heavy gauge metal part of the frame or engine block. Ensure that all installation, operating instructions and safety precautions are understood and observed; then follow the steps outlined in the appropriate section (Charging a battery Installed in a Vehicle or Charging a Battery That has been Removed from a Vehicle). However, there is no guarantee that interference will not occur in a particular installation. EverStart EL224 600 Peak AMP Lithium-Ion Jump Starter/Power Pack Owner's Manual PLEASE SAVE THIS OWNER'S MANUAL AND READ BEFORE EACH USE. and then, at the flick of a switch, it can go from charging traditional 12V automotive systems in . Use common sense. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor. For positive-grounded vehicle, connect NEGATIVE (BLACK) clamp from battery charger to NEGATIVE (NEG, N, ) ungrounded post of battery. A: The problem of plugged in, not charging may be caused by a damaged cord. If the plug does not fit fully into the outlet, reverse the plug. Do not connect clip to carburetor, fuel lines or sheet-metal body parts. If positive post is grounded to the chassis, see 6. If your flashlight doesnt seem to be charging, there are a few things you can do: There are a few other things you should know when trying to charge your Everstart Maxx flashlight. Q: How long does it take a 15 amp charger to charge a car battery? Wait 4 to 5 minutes before a second attempt at starting the engine, if needed. Using the Hanging Hook Do not open the battery charger there are no user-serviceable parts inside. Required fields are marked *. WARNING A spark near the battery may cause an explosion. CAUTION To reduce the risk of product damage: WARNING: Do not put the screw through the plastic housing of the unit as this will permanently damage the unit and cause a potential electrical hazard. Clean battery terminals, taking care to avoid getting corrosive material in eyes. If you need assistance regarding accessories, please contact manufacturer at 1-877-571-2391. By following these simple steps, you will be able to keep your flashlight running at its best! Connect the Positive (RED) battery clamp to the Positive battery post (marked POS, P, + or red). When disconnecting charger, disconnect AC cord, and then remove the Terminals Rings from the battery posts. By following these simple steps, you can ensure that your Everstart Maxx flashlight is always ready. For negative-grounded vehicle, connect POSITIVE (RED) clamp from battery charger to POSITIVE (POS, P, +) ungrounded post of battery. Do not wrap them around the unit or crimp them with a tight band. Discover more about the small businesses partnering with Amazon and Amazons commitment to empowering them. If you need to replace the battery, visit an automotive store or online retailer to find a compatible battery. Source:Amazon.com. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket Press Copyright . Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Be sure area around battery is well ventilated while battery is being charged. Determine which post of battery is grounded (connected) to the chassis. Turning off the controls will not reduce this risk. Proof of purchase may be required by manufacturer. Connect to a heavy gauge metal part of the frame or engine block. Be sure area around battery is well ventilated while battery is being charged. Follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use with this unit. When the battery charger is mounted, do not hang anything additional on the battery charger or risk of breakage may occur. Never allow battery acid to drip on charger when reading gravity or filling battery. To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. These batteries may burst and cause injury to persons and damage property. Connect the battery clamps correctly to the corresponding connectors on. This article will teach you how to charge everstart maxx flashlight correctly. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Save my name, email, and website in this browser for the next time I comment. Do not operate this equipment when you are tired or impaired. Connecting. APPENDIX Turning off the controls will not reduce this risk. Q: How long does it take to fully charge a battery with an EverStart MAXX BC50BE 15 Amp Automotive Battery Charger? second review on an EverStart Maxx battery charger. However, it is important to note that the Everstart Maxx flashlight should only be used with the included USB cable. This charger is not designed for use with every make, manufacturer or model of engine. Opening the battery charger will void manufacturers warranty. If the plug does not fit fully into the outlet, reverse the plug. A: 5 hours following the completion of the batterys external or internal charging (by charger or alternator), or following at least an hour of discharge. These have good quality, and durability, and require little upkeep. A lead acid battery can produce a short circuit current high enough to weld a ring, or similar metal object, to skin causing a severe burn. Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or battery charger. Make sure the surface is flat and free of obstruction so the unit rests flush with the surface. Clean battery terminals, taking care to avoid getting corrosive material in eyes. Grab it and feel for any bulging or other irregularities. Q: What does the green flickering on your portable EverStart MAXX BC50BE 15 Amp Automotive Battery Charger mean? The EverStart series offers both AGM and lead acid batteries. Be aware of first aid procedures in case of accidental contact with battery acid. WARNING: Read all instructions before operating the battery charger. After viewing product detail pages, look here to find an easy way to navigate back to pages you are interested in. See operating instructions for length of charge information. If you need to replace the battery, visit an automotive store or online retailer to find a compatible battery. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. ManualsDock also connects a growing community of active product owners with self-help and product knowledge, there are thousands of manuals from hundreds of big manufacturers. Do not operate the battery charger if it has received a sharp blow, been dropped, or has been otherwise damaged in any way. Increase the separation between equipment and receiver. If you have trouble opening the top cover, try gently prying it open with a knife. Always disconnect the AC plug from the AC outlet first before disconnecting the charger from the battery to be charged. Be extra cautious to avoid dropping a metal tool onto the battery. Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. For. Q: Why cant a dead battery be charged by my EverStart MAXX BC50BE 15 Amp Automotive Battery Charger?